QuickCheckTools

How to bind a quilt

Cut 2½" strips, join them into one long strip, press it in half, sew it to the front of the quilt with mitred corners, then fold it over and stitch it down at the back. Here's each step, and how much binding your quilt needs.

How much binding you need

2½" strips cut across 42" quilting cotton (40" usable), plus 20" for joins and corners, rounded up to the ⅛ yard. For other strip widths, use the quilt binding calculator.

Step by step

  1. Trim the quilt. After quilting, trim the batting and backing level with the edge of the quilt top, and square the corners with a ruler.
  2. Cut the binding strips. Cut 2½" strips across the width of the fabric, selvage to selvage. Use the calculator above for how many.
  3. Join the strips. Lay two strips right sides together at a right angle, sew corner to corner on the diagonal, trim to ¼" and press the seam open. Repeat until you have one long strip. Diagonal seams spread the bulk so the joins lie flat.
  4. Press in half. Fold the strip in half lengthwise, wrong sides together, and press. You now have a 1¼" wide double-fold strip with the raw edges together.
  5. Sew to the front. Starting partway down one side, not at a corner, line the raw edges of the binding up with the edge of the quilt top. Leave a 10" tail and sew with a ¼" seam allowance (a walking foot helps).
  6. Mitre the corners. Stop ¼" before the corner and backstitch. Fold the binding up at 45° away from the quilt, then fold it back down level with the next edge, so the fold sits on the edge you just sewed. Start sewing again from the top edge.
  7. Join the ends. Stop about 12" from where you started. Overlap the two tails by exactly the width of your strip (2½"), trim, open them out, sew them together on the diagonal, trim and finish sewing that last section.
  8. Fold and finish. Fold the binding over the edge to the back so it just covers the stitching line. Hand stitch it down with a blind stitch, or machine stitch from the front in the ditch. Fold the mitres neatly at each corner as you go.

Worked example

A 50" × 65" throw quilt:

  1. Perimeter: 2 × (50 + 65) = 230".
  2. Add 20" for joins and corners: 250".
  3. Strips: 250 ÷ 40 = 6.25, round up to 7 strips of 2½".
  4. Fabric: 7 × 2½" = 17.5", which is ½ yard.

Questions

How wide should quilt binding strips be?

2½" is the most common width for double-fold binding and finishes at about ⅜" on the front. Use 2¼" for a narrower binding on thin quilts, or 2¾" for thick batting.

How much binding do I need?

Add up the four sides of the quilt, add about 20" for the joins and corners, and divide by 40" (the usable width of quilting cotton) to get the number of strips. A 50" × 65" throw needs 7 strips, which is ½ yard of fabric.

Should I hand stitch or machine stitch binding?

Hand stitching the back gives an invisible finish and is traditional for heirloom quilts. Machine binding is faster and stronger, which suits baby quilts and quilts that will be washed often.

Do I need bias binding?

Only for curved or scalloped edges. Straight-grain strips cut across the width of the fabric are fine for straight edges and use less fabric.

What seam allowance do I use for binding?

A ¼" seam allowance with 2½" strips gives a binding that fills to the edge. Some quilters use ⅜" for a fuller binding; keep it the same all the way round.

Why start in the middle of a side?

Starting away from a corner leaves room to join the ends neatly on a straight edge, where the join is easiest to sew and hardest to see.

Free calculator by QuickCheckTools